TM 5-3825-226-24P
(8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for each
special tool, special TMDE, and other special support equipment. When density of equipments supported exceeds
density spread indicated in the basis of issue, the total authorization is increased proportionately.
(9) The statement " END OF FIGURE " appears just below the last item description in Column 5 for a given
figure in both Section 11 and Section Ill.
f. QTY (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the breakout
shown on the illustration/figure, which is prepared for a functional group, subfunctional group, or an assembly. A "V"
appearing in this column in lieu of a quantity indicates that the quantity is variable-and the quantity may vary from
application to application.
4. Explanation of Columns (Section IV).
a. NATIONAL STOCK NUMBER (NSN) INDEX.
(1) STOCK NUMBER column. This column lists the NSN by National Item Identification Number (NIIN) sequence. The
NIIN consists of the last nine NSN
digits of the NSN (i.e., 5305-01-674-1467 ). When using this column to locate an item, ignore the first 4 digits of the
NSN. However, the complete NSN should be used when ordering items by stock number.
(2) FIG. column. This column lists the number of the figure where the item is identified/located. The figures are
in numerical order in Section 11 and Section i.
(3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG.
column. This item is also identified by the NSN listed on the same line.
b. PART NUMBER INDEX. Part numbers in this index are listed by part number in ascending alphanumeric
sequence (i.e., vertical arrangement of letter and number combination which places the first letter or digit of each group
in order A through Z, followed by the numbers O through 9 and each following letter or digit in like order).
(1) CAGEC column. The Commercial and Government (CAGE) Code (C) is a 5-digit alphanumeric code used
to identify the manufacturer, distributor, or Government agency, etc., that supplies the item.
(2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the design and characteristics of the item by means of its
engineering drawings, specifications standards, and inspection requirements to identify an item or range of items.
(3) STOCK NUMBER column. This column lists the NSN for the associated part number and manufacturer
identified in the PART NUMBER and CAGE columns to the left.
(4) FIG. column. This column lists the number of the figure where the item is identified/located in Sections 11
and Ill.
(5) ITEM- column. The item number is that number assigned to the item as it appears in the figure referenced in
the adjacent figure number column.
c. FIGURE AND ITEM NUMBER INDEX.
(1) FIG. column. This column lists the number of the figure where the item is identified/located in Sections 11
and 111.
(2) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in
the adjacent figure number column.
(3) STOCK NUMBER column. This column lists the NSN for the item.
(4) CAGE column. The Commercial and Government Entity (CAGE) is a 5-digit alphanumeric code used to
identify the manufacturer, distributor, or Government agency, etc., that supplies the item.
(5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the design and characteristics of the item by means of its
engineering drawings, specifications standards and inspection requirements to identify an item or range of items.
5. Special Information.
a. USABLE ON CODE. The usable on code appears in the lower left corner of the Description column heading.
Usable on codes are shown as "UOC: “in the Description column (justified left) on the first line following applicable
item description/nomenclature. Uncoded items are applicable to ail models. Identification of the usable on codes used in
the RPSTL are:
Code
Used On
AGW
613BWDNS
AGD
613BWDS
b. FABRICATION INSTRUCTIONS. Bulk materials required to manufacture items are listed in the Bulk Material
Functional Group of this RPSTL. Part numbers for bulk materials are also referenced in the Description column of the
line item entry for the item to be manufactured/fabricated. Detailed fabrication instructions for items source coded to
be manufactured or fabricated are found in TM 5- 3825-226-24.
c. ASSEMBLY INSTRUCTIONS. Detailed assembly instructions for items source coded to be
4
