TM  10-8110-201-14&P (c) Use  a  suitable  lifting  device  (minimum 4,000 lb (1816 kg) capacity) to place the drum on the cargo truck. Remove the towing and lifting yoke  from  the  drum. (d) Repeat  the  procedures  in  (b) and (c) above to  place  the  remaining  drum  on  the  cargo  truck. (e) Connect the lap link of the front chain assembly  (same  as  shown  on  figure  4-4)  to  a shackle on the front drum, and hook the front chain  assembly  over  the  front  of  the  cargo  com- partment. (f) Secure  the  opposite  end  of  the  drum  to  the cargo  truck  by  following  the  procedure  in  (e) above. (g) Connect  the  lap  link,  located  on  the  end  of an  intermediate  chain  assembly,  to  the  free shackle  on  the  first  drum. (h) Connect the lap link, located six links from the hook on the intermediate chain assembly, to  the  shackle  of  the  second  drum. (i) Secure the opposite end of the second drum to the first drum by following the procedures in (g) and (h) above. (j) Hook  two  rear  brackets  over  the  tailgate of  the  cargo  truck. NOTE Be certain rear brackets are located under tailgate step. (k) Hook side bracket on each side of the cargo  compartment  of  the  truck,  and  secure  them to  the  truck  with  the  bracket  screws. (l) Pass the rear chain assembly through the towing  pintle,  and  secure  the  hook  on  the  chain. (m)  Pass  the  free  end  of  the  rear  chain assembly  through  the  two  loops  on  the  rear bracket. (n) Connect the free end of the rear chain assembly to the shackle of the second drum. (o) Install a load binder on the rear chain assembly between the second drum and the rear bracket. (p) Secure the opposite end of the second drum to the cargo truck by following the pro- cedures  (1) thru (o) above. (3) Unloading Filled Fuel Drums From the 5 Ton (4.5 Metric Ton) Cargo Truck. NOTE When a suitable lifting device is to be used to lift the drums for the cargo truck it will not be necessary to lower the tailgate of the cargo truck. (a) Remove  the  load  binders  from  the  rear chain  assemblies. (b) Disconnect the rear chain assemblies from  the  shackles  on  the  third  drum. (c) Disconnect the   intermediate chain assemblies  from  the  shackles  on  the  third  drum. (d) Loosen the screws on the side brackets, and remove the side brackets from the sides of the cargo truck, and remove the third drum from the truck. NOTE If only the drum is to be unloaded at this location, close the cargo truck tailgate. Reinstall the side brackets on the sides of the cargo compartment. Connect the hook on the intermediate chain assem- blies to the rear chain assemblies. In- stall the load binders on the rear chain assemblies between the intermediate chain assemblies and the rear brackets. (e) Disconnect the   intermediate   chain assemblies  from  the  shackles  on  the  second  drum. Remove  the  second  drum  from  the  cargo  truck. NOTE If only two drums are to be unloaded at this location, close the cargo truck tailgate. Reinstall the side brackets on the sides of the cargo compartment. Con- nect an intermediate chain assembly already  connected  to  first  drum shackles. Connect the hooks of the in- termediate chain assemblies to the rear chain assemblies. Install the load binders on the rear chain assemblies bet- ween the intermediate chain assemblies and the rear brackets. (f) Disconnect the   intermediate chain assemblies  from  the  shackles  on  the  first  drum. (g) Disconnect the front chain assemblies from  the  shackles  on  the  first  drum  and  the  cargo compartment. (h) Remove the first drum from the cargo truck. (i) Disconnect  the  rear  chain  assemblies from  the  towing  pintles. (4) Unloading Filled Fuel Drums From the 2-1/2 Ton (2.8 Metric Ton) Cargo Truck. 4 -7