TM 9-2330-267-14&P
S e c t i o n I l l . O R G A N I Z A T I O N A L P R E V E N T I V E M A I N T E N A N C E C H E C K S
A N D S E R V I C E S ( P M C S )
Page
Paragraph Title
Number
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
General PMCS Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
Organizational Preventive Maintenance Checks and Services (PMCS), Table 4-1 . . . . . . . . . . . . . . . . . . . . .
4-4
Reporting Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
Service Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
Specific PMCS Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4
4 - 7 . G E N E R A L .
To ensure that the water tank trailer is ready for operation at all times,it must be inspected systematically so that
defects can be detected and corrected before they result unserious damage or failure. Table 4-1 contains a tabulated
listing of Preventive Maintenance Checks And Services (PMCS) to
personnel.
be performed by organizational maintenance
4-8. SERVICE INTERVALS.
Perform PMCS, found in Table 4-1, at the following intervals:
(1) Perform Quarferly (Q) PMCS once every three months.
(2) Perform Semiannual (S) PMCS once every six months.
(3) Perform Annual (A) PMCS once each year.
4-9. REPORTING REPAIRS.
Report all defects and corrective actions on DA Form 2404. If a serious problem is found, report it to your
supervisor immediately.
4-10. GENERAL PMCS PROCEDURES.
WARNING
Dry cleaning solvent P-D-680 is toxic and flammable. Always wear protective goggles
and gloves, and use only in a well-ventilated area. Avoid contact with skin, eyes, and
clothes, and DO NOT breathe vapors. DO NOT use near open flame or excessive
heat, The solvents flash point is 100°F-138°F (38°C-59°C). If you become dizzy
while using cleaning solvent, immediately get fresh air and medical help. If solvent
contacts eyes, immediately wash your eyes and get medical aid.
a. Keep equipment clean. Dirt, oil, and debris may cover up a serious problem. Clean as you work and as
needed. Use dry cleaning solvent (Item 9, Appendix E) on all metal surfaces. Use soap (Item 8, Appendix E) and water
on rubber, plastic, and painted surfaces.
b. While performing PMCS, inspect the following components:
(1) Bolt, Nuts, and Screws. Ensure that they are not loose, missing, bent, or broken. Tighten any that
are loose.
4-3